The LCS Folding Glide Propeller is built on Lift's 2026 folding propeller redesign, a reshaped collapse and reinforcement at the highest-stress points. On that foundation, the Glide runs its own blade geometry, sized and pitched for efficiency and glide. Blades measure 1.25 inches at the widest section, the narrowest profile in Lift's folding line, with 5.6 inches of pitch on a 6 inch diameter. The profile folds flat against the hub the moment the motor cuts. It ships standard on every 55mm propulsion and runs on any 68mm motor with the LCS Base Plate and LCS Tail Cone installed. Construction is aluminum with stainless steel inserts.

Product Material:

Aluminum with stainless steel inserts
Blade Pitch: 5.6" (142 mm)
Blade Diameter: 6" (152 mm)
Blade Width (widest section): 1.25" (32 mm)

Compatibility:

55mm Motor (native)
68mm Motor (with kit)

LCS Propeller Installation Guide

⚠️ IMPORTANT: It is critical all eFoil equipment is turned off and the battery is disconnected before working with or around the motor or propellers.

Avoid contact with the spinning propeller, as it can cause severe injury or death.
Keep your fingers, toes, and body parts clear of the propeller at all times.
Do not handle the propeller while the battery is installed in the board.
Do not handle your propeller in the water.
Before You Buy

Which Motor Does Your eFoil Have?

The propeller you need depends on your motor size. Measure the diameter of the circular motor face — the end of your propulsion unit — and match it below.

1

Measure across the center of your motor face

Remove your existing propeller if installed. Using a ruler or calipers, measure straight across the circular end of the motor housing. Match your result to the options below.
68mm / 2.68"Motor face diameter
68mm Motor

eFoils with this motor size
- LIFT5All sizes
- LIFT5 FAll sizes
- LIFT4All sizes
- LIFT3All sizes
- LIFT3 FAll sizes
Note on the LCS Base Plate:LIFT5 ships with it pre-installed. LIFT5 F, LIFT4, LIFT3, and LIFT3 F have a bare 68mm motor face — the Base Plate is included in the 68mm Kit and installs first.
55mm / 2.17"Motor face diameter
55mm Motor

eFoils with this motor size
- LIFTXAll sizes
No adapters needed.The 55mm propulsion already has the LCS interface built in. The propeller threads directly onto the motor shaft.
What’s in the Box

Select your motor size above — here’s exactly what ships to you.
68mmLIFT5 · LIFT5 F · LIFT4 · LIFT3 · LIFT3 F
1. 1
  
  LCS Base Plate
  
  Mounts to the 68mm motor face
  
  Included
2. 2
  
  LCS Tail Cone
  
  Installs onto the Base Plate
  
  Included
3. 3
  
  LCS Folding Propeller
  
  Threads onto the Tail Cone
  
  Included
Everything in one box.All 3 components are included in the 68mm LCS Folding Power Propeller — no separate orders needed.
55mmLIFTX · All sizes
1. 1
  
  LCS Folding Propeller
  
  Threads directly onto the 55mm motor shaft
  
  Included
Just the propeller — nothing else needed.No Base Plate, Tail Cone, or adapters required. The 55mm propulsion already has the LCS interface built in.
Glide or Power?

Both propellers fit 55mm and 68mm motors. The difference is in the ride.

LCS Folding Glide Propeller

Narrowest blade · lowest drag · smoothest surf feel

Blade Width1.25" (32mm)

Blade Pitch5.6" (142mm)

Blade Diameter6" (152mm)

MaterialAluminum + Stainless Steel Inserts

Rider level

BeginnerAdvanced

Best for advanced riders focused on surf performance, wave glide, and battery efficiency. May not suit heavier riders wanting more drive off the line.

LCS Folding Power Propeller

Widest blade · more thrust · higher speed under power

Blade Width1.8" (46mm)

Blade Pitch6.3" (160mm)

Blade Diameter6" (152mm)

MaterialAluminum + Stainless Steel Inserts

Rider level

BeginnerAdvanced

Best for heavier riders, those wanting maximum drive off the line, and eFoil surfers who want stronger power and higher speed under throttle.

Which Motor Does Your eFoil Have?

Measure across the center of your motor face

68mm Motor

55mm Motor

What’s in the Box

Glide or Power?

Lift LCS Folding Glide Propeller